Teach Your Kid Electronics

Intermediate · Project 2

Touch Switch

Team up two transistors so the tiny current through your fingertip turns on a light.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Intermediate⏱ About 25 min

🧰 What you need

  • 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
  • 3×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 2×2N3904 transistor (NPN)A tiny electronic switch: a small current into its middle leg (base) controls a bigger current.
  • 1×1 kΩ resistor — brown, black, red, goldColors: brown, black, red, gold.
  • 1×220 Ω resistor — red, red, brown, goldOur go-to LED resistor. Colors: red, red, brown, gold.
  • 1×5 mm LED (any color) — red, orange or yellowA tiny light that only lets current flow one way. The long leg is +.
  • 6×Jumper wire — two long ones for the padsA short wire with stiff ends that push into the breadboard.
  • 1×Aluminum foilKitchen foil conducts electricity. Great for making touch pads.
  • 1×Piece of cardboardA base to tape things onto.

✨ The finished project

A touch switch: two transistors (a Darlington pair) light an LED when a finger bridges two touch pads ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 2N3904EBC 2N3904EBC 1 kΩ 220 Ω +− AAAAAA3 × AA = 4.5 V+− 👆 touch bothpad 1pad 2
A touch switch: two transistors (a Darlington pair) light an LED when a finger bridges two touch pads ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 2N3904EBC 2N3904EBC 1 kΩ 220 Ω +− AAAAAA3 × AA = 4.5 V+− 👆 touch bothpad 1pad 2
Schematic: A touch switch: two transistors (a Darlington pair) light an LED when a finger bridges two touch pads Q2 Q1 +4.5V +4.5V 4.5 V 2N3904 2N3904 1 kΩ pad 1 / pad 2 220 Ω red LED
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

In the last project, a damp finger made the LED glow just a little. Your skin does conduct electricity, but only a teeny bit: about a million times less than a wire! To make a real touch switch, we need more amplifying. The trick: two transistors working as a team.

The Darlington pair

Connect the first transistor’s emitter to the second transistor’s base. Now:

  • Your finger’s tiny current is amplified by transistor 1 (about 100×)…
  • …and that bigger current is amplified again by transistor 2 (another 100×).

That’s 10,000 times in total! Engineers call this a Darlington pair, after Sidney Darlington, who invented it in 1953.

Engineers name transistors Q1, Q2 and so on, so that’s what we’ll call them.

Make the touch pads

Cut two strips of aluminum foil about 3 cm × 4 cm and tape them onto cardboard, side by side with a small gap (about 5 mm) between them. Fold one end of each long jumper wire into its foil pad and tape it down firmly. The metal must touch the foil.

Build it

  1. Transistor 1 (Q1): flat side facing you, E e13, B e14, C e15.

  2. Transistor 2 (Q2): flat side facing you, E e8, B e9, C e10.

  3. Green wire (the team link): c13 (Q1’s emitter) to c9 (Q2’s base).

  4. Red wires (collectors to +): a15 to T+15 (top red + rail, column 15), and a10 to T+10 (top red + rail, column 10).

  5. 1 kΩ resistor: b14 (Q1’s base) to b19. It protects the transistors if the pads ever touch each other.

  6. 220 Ω resistor: b8 (Q2’s emitter) to b4.

  7. LED: long leg in e4, short leg in e3. Then a black wire from a3 to T-3 (top blue − rail, column 3).

  8. Touch pads: plug one pad’s wire into a19 and the other into T+21 (top red + rail, column 21).

  9. Power: battery red into T+1, black into T-2. Touch both pads at once with one finger, and the LED lights up! 👆

How it works

Your finger connects the battery’s + (one pad) to the transistors (the other pad). A tiny current flows through your skin, then into Q1’s base. Q1 amplifies it and passes it to Q2’s base, and Q2 amplifies it again. Now there’s plenty of current to light the LED.

In this circuit the LED sits after the transistors’ emitters, so the transistors use up about 1.3 V of the push. That’s why a red, orange or yellow LED works best. Blue, white and bright green need too much voltage.

Not working?

  • Nothing when touching? Lick your finger (or breathe on it) to make it a little damp, then try again. Check the pad wires are pressed firmly onto the foil.
  • LED always on? The two pads are touching each other. Separate them a bit.
  • Still nothing? Touch the two pad wire ends directly together. If the LED lights, the board is fine and it’s the pads.

Try it!