Intermediate · Project 7
Ping-Pong Flasher
Two transistors and two capacitors make two LEDs take turns blinking, all by themselves.
Build this only with an adult present. Before you start, read our safety notice and disclaimer.
🧰 What you need
- 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
- 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
- 3×AA batteryA regular household battery. Each one gives 1.5 volts.
- 2×2N3904 transistor (NPN)A tiny electronic switch: a small current into its middle leg (base) controls a bigger current.
- 2×22 µF capacitor (can-shaped)A small can-shaped capacitor. The striped leg is −.
- 2×47 kΩ resistor — yellow, violet, orange, goldColors: yellow, violet, orange, gold.
- 2×330 Ω resistor — orange, orange, brown, goldColors: orange, orange, brown, gold.
- 2×5 mm LED (any color) — red works bestA tiny light that only lets current flow one way. The long leg is +.
- 10×Jumper wireA short wire with stiff ends that push into the breadboard.
✨ The finished project
🔣 New schematic symbols
This project’s schematic has some symbols you haven’t seen before. Here’s what they mean.
- Wires crossing (not joined)
When two wires cross with no dot, they are NOT connected: one just passes over the other. Only a dot means joined.
Until now, every circuit has done something only when you did something: pressed a button, covered a sensor. This one runs all by itself: two LEDs take turns flashing, left-right-left-right, like a ping-pong rally. 🏓
Engineers call it an astable multivibrator (“never stays still, shakes back and forth”). It’s been blinking lights since the 1910s!
How it works
There are two transistor switches, Q1 on the top half and Q2 on the bottom. The secret is the two capacitors that cross over: each one connects one transistor’s collector to the other transistor’s base.
- Say Q1 switches on. Its LED lights, and its collector suddenly drops to almost 0 V.
- That sudden drop pushes through capacitor C1 and yanks Q2’s base below 0 V, so Q2 switches off.
- Slowly, the 47 kΩ resistor fills C1 back up until Q2’s base reaches about 0.65 V, and Q2 switches on.
- Now Q2’s collector drops, which kicks Q1 off through C2… and the whole thing repeats, forever!
The speed depends on the resistors and capacitors. With 47 kΩ and 22 µF, each LED flashes about once a second.
Build it
Transistors: Q1 in the top half (flat side facing you) with E d9, B d10, C d11. Q2 in the bottom half: E g9, B g10, C g11.
Bridges for the bottom rails: red T+17 → B+17 (bottom red + rail, column 17), black T-19 → B-19 (bottom blue − rail, column 19).
Emitters to −: a9 → T-8 (top blue − rail, column 8), and j9 → B-8 (bottom blue − rail, column 8).
Base resistors (47 kΩ): stand one between a10 and T+10 (top red + rail, column 10), and the other between j10 and B+10 (bottom red + rail, column 10).
Capacitor C1: across the middle gap, + leg (no stripe) in e13, striped − leg in f13. Yellow wires: e11 → d13 (from Q1’s collector) and g13 → f10 (to Q2’s base).
Capacitor C2: across the gap the other way, + leg in f7, striped − leg in e7. Orange wires: f11 → g7 (from Q2’s collector) and b7 → b10 (to Q1’s base).
LED 1 (top): blue wire b11 → b14; LED short leg e14, long leg e15; 330 Ω resistor standing between a15 and T+15 (top red + rail, column 15).
LED 2 (bottom): blue wire i11 → i14; LED short leg f14, long leg f15; 330 Ω resistor standing between j15 and B+15 (bottom red + rail, column 15).
Power: battery red into T+1, black into T-2. Watch them ping-pong! 🔴⚫ ⚫🔴
Not working?
- Both LEDs on, nothing blinks? Check each capacitor’s stripe (−) leads toward a transistor’s base, and that the yellow and orange wires go to exactly the holes listed.
- One LED on, the other off forever? One of the crossover connections is missing. Trace each capacitor from collector to the other base.
- Nothing lights? Check the bottom rail bridges and that both transistors are the right way round.