Teach Your Kid Electronics

Intermediate · Project 8

555 Blinker

Meet your first chip, the famous 555 timer, and make it flash an LED about once a second.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Intermediate⏱ About 25 min

🧰 What you need

  • 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×4×AA battery holder with wire leadsHolds four AA batteries for 6 volts. Used for the 555 timer chip, which needs a bit more push.
  • 4×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 1×NE555 timer chipOne of the most famous chips ever made: it makes blinks, beeps and timers from a resistor and capacitor.
  • 1×10 kΩ resistor — brown, black, orange, goldColors: brown, black, orange, gold.
  • 1×47 kΩ resistor — yellow, violet, orange, goldColors: yellow, violet, orange, gold.
  • 1×10 µF capacitor (can-shaped)A small can-shaped capacitor. The striped leg is −.
  • 1×330 Ω resistor — orange, orange, brown, goldColors: orange, orange, brown, gold.
  • 1×5 mm LED (any color) — any color worksA tiny light that only lets current flow one way. The long leg is +.
  • 9×Jumper wireA short wire with stiff ends that push into the breadboard.

✨ The finished project

A 555 blinker: NE555 timer, 10k and 47k resistors and a 10 microfarad capacitor flash an LED about once a second ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10µF NE555 10 kΩ 47 kΩ 330 Ω +− AAAAAAAA4 × AA = 6.0 V+−
A 555 blinker: NE555 timer, 10k and 47k resistors and a 10 microfarad capacitor flash an LED about once a second ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10µF NE555 10 kΩ 47 kΩ 330 Ω +− AAAAAAAA4 × AA = 6.0 V+−
Schematic: A 555 blinker: NE555 timer, 10k and 47k resistors and a 10 microfarad capacitor flash an LED about once a second DIS7THR6TRIG2OUT3VCC8RESET4GND1CTRL5NE555U1 + +6.0V +6.0V 6.0 V 10 kΩ 47 kΩ 10 µF 330 Ω red LED
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

🔣 New schematic symbols

This project’s schematic has some symbols you haven’t seen before. Here’s what they mean.

  • Chip

    A chip is drawn as a box with its pins around the edge. The name inside the box says what each pin does; the small number outside is the real pin number (count from the notch). Inputs are usually on the left, outputs on the right, + on top and − at the bottom.

This is your first chip! A chip (also called an integrated circuit) is a whole circuit shrunk down onto a tiny slice of silicon and sealed in a plastic case, with metal legs called pins sticking out. The 555 timer was invented in 1971 and is still one of the best-selling chips ever. Billions have been made! Inside its little black body are about 25 transistors, all arranged to do one job brilliantly: timing.

Placing a chip

Chips sit across the middle gap, with one row of legs in row e and the other in row f, so no two legs are connected by the board. Find the notch (or dot) at one end: that end goes on the left. Pin 1 is then the bottom-left leg, and the numbers count around the chip anticlockwise (the opposite way to a clock’s hands).

Each pin has a job and a short name. Pins the chip listens to are inputs; a pin where the chip sends out its answer is an output. When the output is ON it’s connected to +, and when it’s OFF it’s connected to −.

NE5551GND2TRIG3OUT4RESET5CTRL6THR7DIS8VCC
  • Pin 1 · GND — connect to battery −
  • Pin 2 · TRIG — when this drops below ⅓ of the battery voltage, the output turns ON
  • Pin 3 · OUT — the output, which lights our LED
  • Pin 4 · RESET — must be kept connected to + (or the chip stops)
  • Pin 6 · THR — when this rises above ⅔ of the battery voltage, the output turns OFF
  • Pin 7 · DIS — "discharge": empties the capacitor while the output is OFF
  • Pin 8 · VCC — connect to battery +

Build it

  1. The chip: across the gap, notch on the left, so pins 1–4 are in f10–f13 and pins 8–5 are in e10–e13.

  2. Bottom rail bridges: red T+19 → B+19 (bottom red + rail, column 19), black T-20 → B-20 (bottom blue − rail, column 20).

  3. Power the chip: VCC (pin 8) red wire a10 → T+9 (top red + rail, column 9). GND (pin 1) black wire j10 → B-10 (bottom blue − rail, column 10). RESET (pin 4) red wire j13 → B+13 (bottom red + rail, column 13).

  4. 10 kΩ resistor: stand it between a11 (DIS, pin 7) and T+11 (top red + rail, column 11).

  5. 47 kΩ resistor: c11 (DIS) to c7.

  6. Timing wires: blue b12 (THR, pin 6) → b7; blue d7 → g7 across the gap; blue i11 (TRIG, pin 2) → i7. Now THR, TRIG and the 47 kΩ resistor all meet in column 7.

  7. 10 µF capacitor: + leg in a7, striped − leg in T-7 (top blue − rail, column 7).

  8. LED: 330 Ω resistor i12 (OUT, pin 3) → j16; LED long leg g16, short leg g17; black wire j17 → B-17 (bottom blue − rail, column 17).

  9. Power: 4×AA holder red into T+1, black into T-2. Blink… blink… blink! ✨

How it works

  1. The capacitor fills up through both resistors, and the output is ON (LED lit).
  2. When the capacitor reaches ⅔ of the battery voltage, the THR pin notices and the output switches OFF.
  3. The DIS pin then empties the capacitor through the 47 kΩ resistor.
  4. When it drops to ⅓, the TRIG pin notices and the output switches back ON. Repeat forever!

Engineers have a formula for the speed: 1.44 ÷ ((R1 + 2 × R2) × C) = 1.44 ÷ ((10000 + 2 × 47000) × 0.00001) ≈ 1.4 flashes per second. The build check (the computer program that tests every circuit on this site before it’s published) simulated the whole chip, and it really does blink at about that speed.

Not working?

  • LED stays on or off? Check the chip’s notch is on the left. Backwards, pin 1 is in the wrong place. Then check pins 2 and 6 both reach column 7.
  • Nothing at all? Check the bottom rail bridges, and that RESET (pin 4) goes to +.
  • Very faint or flaky? Use fresh batteries. The NE555 needs at least 4.5 V.

Try it!