Teach Your Kid Electronics

Beginner · Project 2

Light Up an LED

Build your very first circuit, a battery, a resistor and an LED, and make it glow.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Beginner⏱ About 15 min

🧰 What you need

  • 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
  • 3×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 1×220 Ω resistor — red, red, brown, goldOur go-to LED resistor. Colors: red, red, brown, gold.
  • 1×5 mm LED (any color) — any color worksA tiny light that only lets current flow one way. The long leg is +.
  • 2×Jumper wire — one red, one black if you have themA short wire with stiff ends that push into the breadboard.

✨ The finished project

A 3×AA battery pack powering a red LED through a 220 ohm resistor on a breadboard ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 220 Ω +− AAAAAA3 × AA = 4.5 V+−
A 3×AA battery pack powering a red LED through a 220 ohm resistor on a breadboard ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 220 Ω +− AAAAAA3 × AA = 4.5 V+−
Schematic: A 3×AA battery pack powering a red LED through a 220 ohm resistor on a breadboard R1 220 Ω D1 LED + 4.5 V current
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

🔣 New schematic symbols

Tap the Schematic tab above to see this circuit drawn the way engineers draw it: as a map made of symbols. Here’s what each symbol means.

  • Wire

    A line is a wire. Electricity can flow anywhere along it. Bends and corners don’t matter: a schematic only shows what is joined to what, not where things sit on the breadboard.

  • Battery

    The long thin line is the + side and the short thick line is the − side. The number next to it is how many volts it pushes.

  • Current arrow

    Shows which way current flows: out of the battery’s +, through every part, and back into its −.

  • Resistor

    The zigzag is a resistor: it holds the current back. The number next to it is its value in ohms (Ω). Bigger number = less current.

  • LED

    The triangle points the way current is allowed to flow, from the long leg (+) to the bar on the short leg (−). The little arrows are the light coming out.

Time to build! You’ll make a circuit with a loop that goes from the battery, through a resistor, through an LED (a tiny light), and back to the battery. When the loop is complete, the LED lights up.

Meet the LED

LED stands for Light-Emitting Diode. A diode is a one-way street for electricity: current can only flow through it in one direction. So an LED only lights up if it’s plugged in the right way round.

  • The long leg is the + side (called the anode). It connects toward the battery’s +.
  • The short leg is the − side (called the cathode). It connects toward the battery’s −.
  • Can’t tell which leg is longer? Look at the rim around the bottom of the LED. One side is flat, and that’s the − side.

How to read the hole names

The steps below use hole names like c10. The letter is the row and the number is the column, so c10 means row c, column 10. Holes in the power rails (the long + and − strips along the edges) are written with T for the top rails: T+1 is the top red + rail and T-2 is the top blue − rail.

Build it

  1. Red wire (a jumper wire is a short wire with a stiff tip on each end, made for breadboards): push one end into T+10 (top red + rail, column 10) and the other into a10 (row a, column 10). This carries power from the + rail to column 10.

  2. Resistor: bend its legs down and push one into b10 and the other into b15. Resistors don’t have a “right way round,” so either leg can go in either hole. Check the bands: red, red, brown is 220 Ω.

    220 Ω resistor
  3. LED: put the long leg in e15 (the same column as the resistor’s end) and the short leg in e16.

  4. Black wire: connect a16 (the LED’s short-leg column) to T-16 (top blue − rail, column 16). This is the path back to the battery.

  5. Power: put 3 AA batteries in the holder (match the + and − marks inside). Push the red battery wire into T+1 (top red + rail, column 1) and the black battery wire into T-2 (top blue − rail, column 2). Your LED lights up! 🎉 If your holder has an on/off switch, flip it on.

Follow the loop

Trace the path with your finger. Electricity goes:

Battery + → + rail → red wire → column 10 → resistor → column 15 → LED (long leg in, short leg out) → column 16 → black wire → − rail → battery −.

One complete loop: that’s a circuit! Pull out any one part and the loop breaks, so the light goes out.

Why do we need the resistor?

An LED doesn’t limit its own current. Connected straight to a battery, it would gulp way too much current and burn out, sometimes with a little pop. The resistor is the narrow pipe that keeps the flow safe.

Here’s how to work out the current. Each LED uses up some of the battery’s voltage just to turn on (a red LED uses about 2 V). The leftover voltage pushes current through the resistor:

current = (battery volts − LED volts) ÷ resistance

For a red LED: (4.5 − 2) ÷ 220 = 11.4 mA. That’s nice and bright, and safely under the LED’s 20 mA limit.

Different colors need different voltages

Each LED color uses a different amount of voltage. Red, orange and yellow LEDs need about 2 V, but blue, white and bright green LEDs need about 3.2 V. That’s why we use 3 AA batteries: with only 2 (3 V), a blue LED doesn’t get enough push to light at all!

This table works out the current for every color with our 220 Ω resistor:

Current through each LED color with a 220 Ω resistor (fresh batteries in brackets)
LED colorLED "uses"2 × AA (3.0 V)3 × AA (4.5 V)4 × AA (6.0 V)
Red2.0 V4.5 mA (5.5 mA)good11.4 mA (12.7 mA)good18.2 mA (20.0 mA)too much!
Orange2.0 V4.5 mA (5.5 mA)good11.4 mA (12.7 mA)good18.2 mA (20.0 mA)too much!
Yellow2.1 V4.1 mA (5.0 mA)good10.9 mA (12.3 mA)good17.7 mA (19.5 mA)good
Green (classic)2.2 V3.6 mA (4.5 mA)good10.5 mA (11.8 mA)good17.3 mA (19.1 mA)good
Green (bright / "true")3.1 V—won't light6.4 mA (7.7 mA)good13.2 mA (15.0 mA)good
Blue3.2 V—won't light5.9 mA (7.3 mA)good12.7 mA (14.5 mA)good
White3.2 V—won't light5.9 mA (7.3 mA)good12.7 mA (14.5 mA)good

Current through each LED color with a 220 Ω resistor ("new" = brand-new batteries)

  • Red uses 2.0 V

    2 × AA
    4.5 mAnew: 5.5 mAgood
    3 × AA
    11.4 mAnew: 12.7 mAgood
    4 × AA
    18.2 mAnew: 20.0 mAtoo much!
  • Orange uses 2.0 V

    2 × AA
    4.5 mAnew: 5.5 mAgood
    3 × AA
    11.4 mAnew: 12.7 mAgood
    4 × AA
    18.2 mAnew: 20.0 mAtoo much!
  • Yellow uses 2.1 V

    2 × AA
    4.1 mAnew: 5.0 mAgood
    3 × AA
    10.9 mAnew: 12.3 mAgood
    4 × AA
    17.7 mAnew: 19.5 mAgood
  • Green (classic) uses 2.2 V

    2 × AA
    3.6 mAnew: 4.5 mAgood
    3 × AA
    10.5 mAnew: 11.8 mAgood
    4 × AA
    17.3 mAnew: 19.1 mAgood
  • Green (bright / "true") uses 3.1 V

    2 × AA
    —won't light
    3 × AA
    6.4 mAnew: 7.7 mAgood
    4 × AA
    13.2 mAnew: 15.0 mAgood
  • Blue uses 3.2 V

    2 × AA
    —won't light
    3 × AA
    5.9 mAnew: 7.3 mAgood
    4 × AA
    12.7 mAnew: 14.5 mAgood
  • White uses 3.2 V

    2 × AA
    —won't light
    3 × AA
    5.9 mAnew: 7.3 mAgood
    4 × AA
    12.7 mAnew: 14.5 mAgood

See how 3 × AA is “good” for every color? That’s why this project uses 3 batteries and a 220 Ω resistor: the same parts work no matter which LED you pick. (Brand-new batteries push a little harder than 1.5 V, so the table checks those too. With 4 batteries, a red LED gets right up to its limit.)

Not lighting up?

  • LED backwards? This is the most common mix-up. Flip it so the long leg is in e15.
  • Wrong column? The resistor’s end and the LED’s long leg must be in the same column (15). Rows a–e in that column are all connected.
  • Batteries? Check they’re the right way round in the holder and not used up. Is the holder’s switch on?
  • Loose wire? Push every leg and wire firmly into its hole.
  • Across the gap? Everything in this build stays in rows a–e. Rows f–j are a separate strip.

Try it!