Teach Your Kid Electronics

Advanced · Project 12

Loudspeaker Amplifier

The 555 can make a note, but only a quiet one. An LM386 audio amplifier chip makes it twenty times bigger and loud enough to fill a room, with a volume knob.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Advanced⏱ About 35 min

🧰 What you need

  • 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×4×AA battery holder with wire leadsHolds four AA batteries for 6 volts. Used for the 555 timer chip, which needs a bit more push.
  • 4×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 1×NE555 timer chipOne of the most famous chips ever made: it makes blinks, beeps and timers from a resistor and capacitor.
  • 1×LM386 audio amplifierMakes a weak sound signal strong enough to drive a speaker.
  • 1×Push button (tactile switch)A little button with 4 legs. It connects its two sides only while you press it.
  • 1×10 kΩ potentiometer (knob)A resistor you can change by turning a knob. Three legs: two ends and a middle "wiper".
  • 1×1 kΩ resistor — brown, black, red, goldColors: brown, black, red, gold.
  • 2×10 kΩ resistor — brown, black, orange, goldColors: brown, black, orange, gold.
  • 1×47 kΩ resistor — yellow, violet, orange, goldColors: yellow, violet, orange, gold.
  • 1×0.1 µF capacitorA tiny charge bucket. Fills and empties thousands of times a second in a tone circuit.
  • 1×1 µF capacitorA small can-shaped capacitor. The striped leg is −.
  • 1×220 µF capacitor (can-shaped)A medium can that passes sound on to a speaker while blocking the steady voltage. The striped leg is −.
  • 1×Passive buzzer — or a small 8 Ω speaker, which sounds even betterA tiny speaker. It needs a fast on-off signal (like from a 555 chip) to make a tone.
  • 1×Small speaker, 8 Ω — optionalLouder and better-sounding than a passive buzzer for music and radio.
  • 14×Jumper wireA short wire with stiff ends that push into the breadboard.

✨ The finished project

A loudspeaker amplifier: a 555 note goes through a volume knob into an LM386, which drives the speaker through a 220 µF capacitor ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10kΩ 0.1µF 1µF 220µF NE555 LM386 +passive 1 kΩ 10 kΩ 10 kΩ 47 kΩ AAAAAAAA4 × AA = 6.0 V+−
A loudspeaker amplifier: a 555 note goes through a volume knob into an LM386, which drives the speaker through a 220 µF capacitor ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10kΩ 0.1µF 1µF 220µF NE555 LM386 +passive 1 kΩ 10 kΩ 10 kΩ 47 kΩ AAAAAAAA4 × AA = 6.0 V+−
Schematic: A loudspeaker amplifier: a 555 note goes through a volume knob into an LM386, which drives the speaker through a 220 µF capacitor DIS7THR6TRIG2OUT3VCC8RESET4GND1CTRL5NE555U1 + + IN+3IN-2OUT5GAIN11VS6GAIN88GND4BYPASS7LM386U2 + + +6.0V +6.0V +6.0V 6.0 V 1 kΩ 10 kΩ 0.1 µF 10 kΩ PLAY 47 kΩ volume 1 µF 220 µF passive buzzer
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

In the Light Theremin and the 555 Tone Keyboard, the 555 played straight into a passive buzzer. It works, but it’s quiet. To fill a room with sound you need an amplifier: a circuit that makes a signal bigger. In this project the LM386, a chip made just for driving speakers, makes the note 20 times bigger, and a knob sets the volume.

The LM386 audio amplifier

LM3861GAIN12IN-3IN+4GND5OUT6VS7BYPASS8GAIN8
  • Pin 1 · GAIN1 — not used (a capacitor here to GAIN8 makes it 200× instead of 20×)
  • Pin 2 · IN- — connect to −
  • Pin 3 · IN+ — the sound goes in here
  • Pin 4 · GND — battery −
  • Pin 5 · OUT — the big sound comes out (through a capacitor to the speaker)
  • Pin 6 · VS — battery +
  • Pin 7 · BYPASS — not used

Three ideas make it work:

  1. The volume knob. The 555’s output goes through 47 kΩ into the knob. The knob’s middle leg picks off anywhere from nothing (silent) to about three quarters of a volt, which is plenty, since the LM386 multiplies it by 20.
  2. Capacitors pass wobbles, not steady voltage. The LM386 only wants the changes in the signal, so a 1 µF capacitor sits in front of it. A capacitor can’t pass a steady current, only changes.
  3. The output rests in the middle. The LM386’s output sits at half the battery voltage and swings up and down from there. A steady current through the speaker would just heat it up, so a big 220 µF capacitor passes on only the swings.

Build it

  1. The 555 note: pin 1 in f5. Red a5 → T+5 (top red + rail, column 5); black j5 → B-5 (bottom blue − rail, column 5). 1 kΩ a6 → T+7 (top red + rail, column 7); 10 kΩ c6 → c2. Blue b7 → b2, e2 → f2, i6 → i2. 0.1 µF capacitor a2 → T-2 (top blue − rail, column 2).

  2. PLAY button: 10 kΩ pull-down j8 (RESET) → B-9 (bottom blue − rail, column 9). White h8 → h10. Button in e10, f10, e12, f12. Red a12 → T+11 (top red + rail, column 11).

  3. Bottom − rail: black T-1 → B-1 (bottom blue − rail, column 1).

  4. Volume: 47 kΩ g7 (555 OUT) → g14. Knob legs in h14, h15, h16. Black j16 → B-16 (bottom blue − rail, column 16).

  5. Into the amplifier: 1 µF capacitor + i15 (the knob’s middle leg), − i18. Orange h18 → h22 (IN+).

  6. LM386: notch on the left, pin 1 in f20. Red a22 → T+22 (top red + rail, column 22); black j23 → B-23 (bottom blue − rail, column 23); black j21 (IN−) → B-21 (bottom blue − rail, column 21).

  7. Speaker: 220 µF capacitor + c23 (OUT), − c27. Passive buzzer (or speaker) + b27, − b30. Black a30 → T-29 (top blue − rail, column 29).

  8. Power: 4×AA red into T+1, black into T-3. Hold PLAY and turn up the volume! 🔊

The build check simulated the speaker’s current wave by wave: with PLAY held it vibrates about 690 times a second at full and half volume, and it’s silent with PLAY released.

Not working?

  • Silent? Turn the volume knob both ways. Check the LM386’s notch is on the left and the 220 µF capacitor’s stripe faces the speaker.
  • Quiet, even at full volume? Check the LM386’s power wires. A real 8 Ω speaker is much louder than a buzzer.
  • A buzz or hum all the time? Check the PLAY pull-down: the 555 should be silent until you press PLAY.

Try it!