Advanced · Project 6
LED Chaser
Ten LEDs in a row and a light that runs along them, over and over. A 555 clock and a CD4017 counter make it happen, on your first full-size breadboard.
Build this only with an adult present. Before you start, read our safety notice and disclaimer.
🧰 What you need
- 1×Full-size breadboardThe big brother of the half-size board: twice as long, with room for several chips.
- 1×4×AA battery holder with wire leadsHolds four AA batteries for 6 volts. Used for the 555 timer chip, which needs a bit more push.
- 4×AA batteryA regular household battery. Each one gives 1.5 volts.
- 1×NE555 timer chipOne of the most famous chips ever made: it makes blinks, beeps and timers from a resistor and capacitor.
- 1×CD4017 decade counterCounts clock pulses and turns on one of its ten outputs at a time, in order. Made for LED chasers.
- 1×10 kΩ resistor — brown, black, orange, goldColors: brown, black, orange, gold.
- 1×22 kΩ resistor — red, red, orange, goldColors: red, red, orange, gold.
- 1×10 µF capacitor (can-shaped)A small can-shaped capacitor. The striped leg is −.
- 10×5 mm LED (any color) — any colorsA tiny light that only lets current flow one way. The long leg is +.
- 30×Jumper wireA short wire with stiff ends that push into the breadboard.
✨ The finished project
↔ Big board! Scroll sideways to see all of it.
This is the classic “running lights” circuit, like the lights around a fairground sign. The CD4017 is a decade counter: it has ten outputs, Q0 to Q9, and exactly one of them is on at a time. Each tick of its clock moves the “on” to the next output. After Q9 it goes back to Q0.
It’s big, so it’s built on a full-size breadboard. Full-size boards work exactly like half-size ones, just longer.
- Pin 8 · VSS — connect to battery −
- Pin 12 · CO — carry out: for linking two counters (not used)
- Pin 13 · INH — "inhibit": ON pauses counting (we keep it OFF)
- Pin 14 · CLK — clock in: each time this goes ON, move to the next output
- Pin 15 · MR — master reset: ON jumps back to Q0 (we keep it OFF)
- Pin 16 · VDD — connect to battery +
Build it
Rail bridges: red T+47 → B+47 (bottom red + rail, column 47), black T-46 → B-46 (bottom blue − rail, column 46). (Some full-size boards have a break in the middle of each rail. If yours has a gap in the red and blue lines, bridge it with a short wire.)
The 555 clock: pin 1 in f5. Red a5 → T+5 (top red + rail, column 5); black j5 → B-5 (bottom blue − rail, column 5); red j8 → B+8 (bottom red + rail, column 8). 10 kΩ a6 → T+7 (top red + rail, column 7); 22 kΩ c6 → c2. Blue b7 → b2, e2 → f2, i6 → i2. 10 µF capacitor + a2, − T-2 (top blue − rail, column 2).
The CD4017: notch on the left, pin 1 in f14. Red a14 → T+13 (top red + rail, column 13); black j21 → B-21 (bottom blue − rail, column 21); black a15 (MR) → T-15; black a17 (INH) → T-17.
Clock: yellow wires h7 (555 OUT) → h10, f10 → e10 over the gap, c10 → c16 (CLK).
Ten LEDs in a row, each with its long leg in row j and its short leg in the bottom − rail:
- LED 0: long leg j26, short leg B-25.
- LED 1: long leg j28, short leg B-27.
- LED 2: long leg j30, short leg B-29.
- LED 3: long leg j32, short leg B-31.
- LED 4: long leg j34, short leg B-33.
- LED 5: long leg j36, short leg B-35.
- LED 6: long leg j38, short leg B-37.
- LED 7: long leg j40, short leg B-39.
- LED 8: long leg j42, short leg B-41.
- LED 9: long leg j44, short leg B-43.
Output wires, one LED at a time. Wires marked “hop” jump the middle gap at the LED’s column:
- Q0 (pin 3) → LED 0: g16 → g26
- Q1 (pin 2) → LED 1: h15 → h28
- Q2 (pin 4) → LED 2: i17 → i30
- Q3 (pin 7) → LED 3: j20 → g32
- Q4 (pin 10) → LED 4: b20 → b34, then hop e34 → f34
- Q5 (pin 1) → LED 5: j14 → h36
- Q6 (pin 5) → LED 6: j18 → i38
- Q7 (pin 6) → LED 7: j19 → g40
- Q8 (pin 9) → LED 8: c21 → c42, then hop e42 → f42
- Q9 (pin 11) → LED 9: d19 → d44, then hop e44 → f44
Power: 4×AA red into T+1, black into T-3. Whoosh! 🏃
How it works
The 555 ticks a bit more than twice a second. Each tick, the CD4017 switches its current output off and the next one on. Because only one output is ever on, only one LED lights. Like the Binary Counter, the CD4000 outputs only push about 5 mA, so no LED resistors are needed.
The build check simulated ten ticks and confirmed the light visits LED 0, 1, 2 … 9 and back to 0, in order.
Not working?
- Light jumps around out of order? Two output wires are swapped. Check each one against the list above.
- One LED never lights? It’s backwards (long leg in row j), or its wire is in the wrong row.
- Nothing moves? Check MR and INH go to −, and the three yellow clock wires.
- Two LEDs at once? Two output wires share a column. Every output column should have exactly one wire.