Advanced · Project 15
Wired RC Car
The grand finale! Build a car and a handheld controller joined by a cable. Four buttons and a DRV8833 motor driver steer two wheels forwards, backwards and round in circles.
Build this only with an adult present. Before you start, read our safety notice and disclaimer.
🧰 What you need
- 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
- 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
- 3×AA batteryA regular household battery. Each one gives 1.5 volts.
- 1×DRV8833 motor driver moduleA small board that drives two motors forwards and backwards from four input signals.
- 1×2-wheel robot car chassisA flat base with two TT motors and wheels, plus a little swivel wheel at the front. Thick cardboard works too.
- 2×TT gear motor — usually included with the chassisThe yellow motor used in robot cars. Runs on 3–6 V.
- 1×Ribbon cable (4 wires, about 1 m)Several thin wires stuck side by side: a neat way to run long connections.
- 4×Push button (tactile switch)A little button with 4 legs. It connects its two sides only while you press it.
- 4×10 kΩ resistor — brown, black, orange, goldColors: brown, black, orange, gold.
- 16×Jumper wireA short wire with stiff ends that push into the breadboard.
✨ The finished project
You’ve made it to the last project! Everything comes together here: buttons, pull-down resistors, driver chips and motors. You’ll build a car with two motorized wheels, steered from a handheld controller.
The controller is your breadboard: it holds the batteries, four buttons and the motor driver. A long ribbon cable (four thin wires stuck side by side) runs from the controller to the two motors on the car. Keeping the batteries in your hand makes the car lighter and faster.
Driving both ways: the H-bridge
The Robot Muscles chip could only switch a motor on and off. To drive backwards, the current through the motor must flow the other way. That takes an H-bridge: four switches around the motor, arranged like the letter H.
- Close the top-left and bottom-right switches: current flows through the motor one way. Forward!
- Close the top-right and bottom-left instead: current flows the other way. Reverse!
The DRV8833 module has two H-bridges, one for each wheel, controlled by four inputs:
| Pressed | Left wheel | Right wheel | The car… |
|---|---|---|---|
| LF + RF | forward | forward | drives straight |
| LB + RB | back | back | reverses |
| LB + RF | back | forward | spins left |
| LF + RB | forward | back | spins right |
| RF only | stopped | forward | turns gently left |
This is tank steering, just like a real tank or a digger: no steering wheel, just two sides going at different speeds or directions.
- Pin 1 · OUT1 — left motor lead
- Pin 2 · OUT2 — left motor lead
- Pin 3 · OUT3 — right motor lead
- Pin 4 · OUT4 — right motor lead
- Pin 5 · GND — battery −
- Pin 6 · VCC — battery +
- Pin 7 · IN4 — right wheel back (RB)
- Pin 8 · IN3 — right wheel forward (RF)
- Pin 9 · IN2 — left wheel back (LB)
- Pin 10 · IN1 — left wheel forward (LF)
- Pin 11 · ULT — fault warning (not used)
- Pin 12 · EEP — "enable": connect to + or it sleeps
Build the car
- Assemble the chassis with its two motors and wheels (or tape two TT motors to the sides of a stiff piece of cardboard, with a smooth bead or bottle cap underneath as a third “wheel”).
- Solder or twist a long lead onto each motor terminal, with an adult’s help. Use four wires peeled off a rainbow ribbon cable, about 1 m long.
- Label the wires: left motor ⚫⚪, right motor ⚫⚪ (or note their colors).
Build the controller
Driver module: across the gap, in the columns shown, so OUT1 is in f14. Red j19 (VCC) → B+19 (bottom red + rail, column 19); black j18 (GND) → B-17 (bottom blue − rail, column 17); red a14 (EEP) → T+14 (top red + rail, column 14).
Rail bridges: red T+29 → B+29 (bottom red + rail, column 29), black T-11 → B-11 (bottom blue − rail, column 11).
Left-hand buttons: LF in e3, f3, e5, f5, LB in e8, f8, e10, f10. Red a3 → T+3 (top red + rail, column 3) and a8 → T+8 (top red + rail, column 8). Green d5 → d16 (IN1); orange c10 → c17 (IN2).
Right-hand buttons: RF in e24, f24, e22, f22, RB in e28, f28, e26, f26. Red a24 → T+25 (top red + rail, column 25) and a28 → T+28 (top red + rail, column 28). Blue b22 → b18 (IN3); yellow c26 → c19 (IN4).
Pull-downs (10 kΩ each, so a motor stops when you let go): j5 → B-5 (bottom blue − rail, column 5), j10 → B-10 (bottom blue − rail, column 10), j22 → B-22 (bottom blue − rail, column 22), j26 → B-26 (bottom blue − rail, column 26).
Cable to the car: left motor’s wires into g14 (OUT1) and g15 (OUT2); right motor’s into h16 (OUT3) and h17 (OUT4).
Power: 3×AA red into T+1, black into T-2. Hold the car up and test each button. 🏎️
The build check drove the simulated car through every move in the table, checking each wheel spins and spins the right way, and that pressing both buttons for one wheel stops it.
Not working?
- Nothing moves? Check EEP is connected to +: without it the driver sleeps. Check VCC and GND.
- A wheel only goes one way? Check that wheel’s other button, its wire to IN2 or IN4, and its pull-down.
- The wheels twitch but don’t turn? The batteries may be tired: motors need fresh ones. Or the car is too heavy: take off anything you don’t need.
- A wheel turns without any button? A button is rotated so it’s always pressed. Give it a quarter turn.
Try it!
You did it! 🎉
From lighting your first LED to driving your own car, you’ve learned how electricity flows, how to read resistors, how transistors switch and amplify, how chips count, remember and decide, and how motors are driven. That’s real electronics, the same ideas inside every phone, game console and robot. Well done, engineer!