Teach Your Kid Electronics

Beginner · Project 1

Meet Electricity

What electricity is, how a breadboard works inside, and how to read the secret color code on a resistor.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Beginner⏱ About 20 min

🧰 What you need

  • 1×Half-size breadboard — just to look at todayA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×3×AA battery holder with wire leads — just to look at todayHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
  • 1×100 Ω resistorA small resistor. Colors: brown, black, brown, gold.
  • 1×220 Ω resistorOur go-to LED resistor. Colors: red, red, brown, gold.
  • 1×1 kΩ resistorColors: brown, black, red, gold.
  • 1×10 kΩ resistorColors: brown, black, orange, gold.

Welcome, builder! Before we make anything light up, let’s get to know the invisible stuff that makes it all work: electricity. This first project is mostly about learning, and in the next one you’ll use everything here to build your first circuit.

What is electricity?

Everything is made of tiny particles called atoms. Inside atoms are even tinier particles called electrons. In metals like copper, some electrons can hop from atom to atom. When lots of electrons move along a wire together, that flow is electricity.

You can’t see electrons, so it helps to imagine water flowing through pipes:

  • Voltage

    How hard the electricity is pushed

    Like water: The water pressure from a pump

    Measured in: volts (V)

  • Current

    How much electricity is flowing

    Like water: How much water flows through the pipe

    Measured in: amps (A) or milliamps (mA)

  • Resistance

    How much something slows the flow down

    Like water: A narrow, squeezed part of the pipe

    Measured in: ohms (Ω)

A battery is the pump. One AA battery pushes with 1.5 volts. Put batteries end-to-end (we call that in series) and their pushes add up. That’s why our battery holder, which holds three AAs, gives 3 × 1.5 = 4.5 volts.

Electricity needs a loop

Electricity only flows if it has a complete path that goes out of the battery’s + end, through your parts, and back into the battery’s − end. That loop is called a circuit. If there’s a gap anywhere, the flow stops, like a broken pipe. That’s called an open circuit.

Meet the breadboard

Pick up your breadboard and turn it over (don’t peel off the sticky back!). It’s a board full of holes, and under the holes are hidden metal strips. When you push a wire into a hole, a metal clip grabs it. Everything pushed into the same strip is connected.

An empty breadboard with some of its hidden metal strips highlighted ++−−++−−aabbccddeeffgghhiijj115510101515202025253030
An empty breadboard with some of its hidden metal strips highlighted ++−−++−−aabbccddeeffgghhiijj115510101515202025253030
Each colored box is one hidden metal strip. Holes inside the same box are connected.a–e of column 5f–j of column 5 (a different strip — the middle gap separates them)a–e of column 12the whole red + railthe whole blue − rail

The rules to remember:

  • Rows a–e in one numbered column are all connected to each other.
  • Rows f–j in that column are connected too, but they’re a separate strip. The gap down the middle splits them.
  • The long + and − rails along the top and bottom are connected all the way along. We plug the battery into these, so power is easy to reach from anywhere.
  • Columns are not connected to their neighbors. Column 5 and column 6 are strangers!

Meet the resistor

A resistor is the narrow pipe in our water picture: it lets some current through, but not too much. Resistors protect delicate parts like LEDs from getting too much current and burning out.

Resistors are too small to print numbers on, so instead they wear colored stripes called bands. Each color stands for a number.

How to read the bands

  1. Find the gold (or silver) band and turn the resistor so it’s on the right. That’s the tolerance band, which tells you how exact the resistor is. Gold means within 5%.
  2. Band 1 (far left) is the first digit.
  3. Band 2 is the second digit.
  4. Band 3 is the multiplier: it tells you how many zeros to add on the end.
ColorBand 1 & 2
(digit)
Band 3
(multiplier)
Band 4
(tolerance)
Black0× 1 add no zeros—
Brown1× 10 add 1 zero±1%
Red2× 100 add 2 zeros±2%
Orange3× 1 k add 3 zeros—
Yellow4× 10 k add 4 zeros—
Green5× 100 k add 5 zeros±0.5%
Blue6× 1 M add 6 zeros±0.25%
Violet7— ±0.1%
Grey8— ±0.05%
White9— —
Gold—× 0.1 ±5%
Silver—× 0.01 ±10%

Remember the digit order 0–9 with: Black Bears Roam Our Yards, Gobbling Blueberries Very Greedily — Wow!
(black, brown, red, orange, yellow, green, blue, violet, grey, white)

Let’s try one together

220 Ω resistor
  • Band 1 is red → 2
  • Band 2 is red → 2
  • Band 3 is brown → add 1 zero
  • So it’s 2, 2, and one zero = 220 Ω (220 ohms). This is the resistor you’ll use in the next project!

Now play with the decoder. Change the colors and watch the value change:

🔍 Resistor decoder

Pick the colors you see (start from the end away from the gold or silver band) and the decoder works out the value. Or type a value to see its colors.

Resistor with the selected bands

220 Ω ±5%

red (2), red (2) → 22, brown → × 10 → 220 Ω

Hands-on: the resistor sort

Take your four resistors (100 Ω, 220 Ω, 1 kΩ and 10 kΩ) and mix them up on the table. Now, using only the color bands, figure out which is which and line them up from smallest to biggest. (“k” means kilo, or a thousand, so 1 kΩ = 1,000 Ω.)

Warm up with these mystery resistors first:

  1. Mystery resistor A

    A mystery resistor
    Show answer

    brown, black, red, gold → 1 kΩ

  2. Mystery resistor B

    A mystery resistor
    Show answer

    red, red, brown, gold → 220 Ω

  3. Mystery resistor C

    A mystery resistor
    Show answer

    brown, black, orange, gold → 10 kΩ

  4. Mystery resistor D

    A mystery resistor
    Show answer

    brown, black, brown, gold → 100 Ω

Quick check

What pushes electricity around a circuit? The battery’s voltage, the “pump pressure.”

Are holes a7 and b7 connected? Yes! Same column, both in rows a–e.

Are holes e7 and f7 connected? No. The middle gap separates rows a–e from f–j.

Yellow, violet, red, gold — what’s the value? 4, 7, then add 2 zeros: 4,700 Ω = 4.7 kΩ.

Great work! In the next project you’ll plug a battery, a resistor and a light into the breadboard and make your very first working circuit.