Glossary
Every electronics word on this site, in plain words. On project pages these words have a dotted underline: tap or point at one to see what it means. Each word here links to the place it’s first explained.
#
- 7-segment display
- A number display made of seven bar-shaped LEDs (a to g). Light the right bars and you get any digit.First explained in Two-Digit Counter →
- 74HC and CD4000 chips
- Two families of logic chips. 74HC chips have strong outputs and run on 2–6 V. CD4000 chips run on 3–18 V and their outputs only push about 5 mA.First explained in Logic Gate Puzzles →
- 555 timer
- A famous timing chip from 1971. With a resistor and a capacitor it can blink lights or make tones.First explained in 555 Blinker →
A
- Active buzzer
- A buzzer with its own little circuit inside: connect a battery and it beeps.First explained in Doorbell Buzzer →
- Alligator clip
- A spring-loaded metal clip with teeth, for gripping a wire or part without plugging it in.First explained in Steady-Hand Game →
- AM (amplitude modulation)
- A way of sending sound by radio: the sound makes the radio wave stronger and weaker.First explained in AM Radio →
- Amp and milliamp (A, mA)
- Units for measuring current. A milliamp (mA) is a thousandth of an amp. An LED needs about 10 mA.First explained in Meet Electricity →
- Amplifier
- A circuit that makes a signal bigger, like turning a whisper into a shout.First explained in Clap-On Light →
- Amplify
- To make bigger. A transistor amplifies: a small current controls a much bigger one.First explained in Transistor Switch →
- AND
- A logic rule: the answer is yes (1) only if every input is yes.First explained in Push-Button Light →
- Anode
- The + side of an LED or diode. On an LED it’s the long leg.First explained in Light Up an LED →
- Astable multivibrator
- A circuit that never stays still: it flips back and forth by itself, like the Ping-Pong Flasher.First explained in Ping-Pong Flasher →
- Atom
- One of the tiny particles that everything is made of. Far too small to see.First explained in Meet Electricity →
B
- Base
- The control leg of a transistor (B). A tiny current here switches it on.First explained in Transistor Switch →
- Battery
- Stored-up electricity that pushes current around a circuit, out of its + end and back into its − end. Like a pump in a water pipe.First explained in Meet Electricity →
- Binary
- Counting with only two digits, 0 and 1. Each place is worth double the one to its right: 1, 2, 4, 8…First explained in Binary Counter →
- Bit
- A single 1 or 0. It’s the smallest piece of information a computer can store.First explained in Flip-Flop Memory →
- Bounce
- When a button’s metal contacts touch, spring apart and touch again in a split second, so one press counts as several.First explained in Flip-Flop Memory →
- Breadboard
- A board full of holes with hidden metal strips underneath. Parts pushed into the same strip are connected, so you can build circuits without soldering.First explained in Meet Electricity →
- Buzzer
- A part that turns electricity into sound with a disc that wiggles back and forth.First explained in Doorbell Buzzer →
C
- Capacitance
- How much charge a capacitor can hold: the size of the bucket. Measured in microfarads.First explained in Glow That Fades →
- Capacitor
- A tiny bucket for electricity: it fills up with charge and can let it back out later.First explained in Glow That Fades →
- Carry
- When one digit rolls over from 9 to 0 and the next digit goes up by one, like 19 + 1 = 20.First explained in Two-Digit Counter →
- Cathode
- The − side of an LED or diode. On an LED it’s the short leg, next to the flat edge.First explained in Light Up an LED →
- Charge
- Stored-up electricity, like the water in a bucket. Capacitors and batteries hold charge.First explained in Glow That Fades →
- Chip (integrated circuit)
- A whole circuit shrunk onto a tiny slice of silicon and sealed in a plastic case, with metal legs called pins.First explained in 555 Blinker →
- Circuit
- A complete loop that electricity can flow around: out of the battery, through the parts, and back again.First explained in Meet Electricity →
- Clock
- A signal that ticks ON and OFF over and over. Each tick tells chips like counters and flip-flops to take their next step.First explained in Flip-Flop Memory →
- Coil
- Wire wound round and round many times. Motors are full of them.First explained in Spinning Fan →
- Collector
- The leg of a transistor (C) where the big current comes in.First explained in Transistor Switch →
- Color bands
- The colored stripes on a resistor. Each color stands for a number, and together they give the resistor’s value.First explained in Meet Electricity →
- Common cathode
- A display where all the LEDs’ − legs are joined inside to one pin.First explained in Two-Digit Counter →
- Comparator
- A chip that compares two voltages and switches its output depending on which one is higher.First explained in Fever Alarm →
- Conduct
- To let electricity flow through. Metal conducts very well; plastic and dry air don’t.First explained in Steady-Hand Game →
- Counter (chip)
- A chip that adds one each time its clock input ticks, and shows the count on its outputs.First explained in Binary Counter →
- Current
- How much electricity is flowing, like how much water flows through a pipe. Measured in amps or milliamps.First explained in Meet Electricity →
D
- Darlington pair
- Two transistors teamed up so the first one’s output feeds the second one’s base. Together they amplify about 10,000 times.First explained in Touch Switch →
- Decade counter
- A counter that counts 10 steps (0 to 9) and then starts again.First explained in LED Chaser →
- Decoder
- A chip that turns a number in binary into something else, like the bars of a digit on a display.First explained in Two-Digit Counter →
- Diffuser
- Something cloudy (like half a ping-pong ball) that spreads light out, so separate colors blend into one.First explained in Color Mixer →
- Diode
- A part that only lets current flow one way, like a one-way street. The band marks its − end.First explained in Light Up an LED →
- Driver chip
- A chip full of strong switches, so tiny signals from buttons or other chips can run motors and lights.First explained in Robot Muscles →
E
- Electricity
- Electrons flowing along a path, like water flowing through a pipe. It can light lights, make sounds and spin motors.First explained in Meet Electricity →
- Electron
- An even tinier particle inside atoms. When lots of electrons move along a wire together, that’s electricity.First explained in Meet Electricity →
- Emitter
- The leg of a transistor (E) where all the current leaves, toward −.First explained in Transistor Switch →
- Emitter follower
- A transistor with its collector on +: the emitter copies the base’s voltage (about 0.7 V lower) but can supply much more current.First explained in Electronic Dice →
- Enable
- An input that must be ON for a chip to do its job (like counting).First explained in Binary Counter →
F
- Ferrite
- A dark, magnetic material. A ferrite rod inside an antenna coil gathers in radio waves.First explained in AM Radio →
- Flip-flop
- A tiny memory circuit that stores one bit until it’s told to save a new one.First explained in Flip-Flop Memory →
- Floating input
- A chip input connected to nothing. It picks up noise and flickers randomly between 0 and 1.First explained in Logic Gate Puzzles →
- Flyback diode
- A diode across a motor that gives its voltage spike a safe path when it switches off, protecting the transistor.First explained in Spinning Fan →
- Frequency
- How many times a second something wiggles. Every radio station sends on its own frequency.First explained in AM Radio →
G
- Gain
- How many times bigger an amplifier makes a signal. A gain of 100 turns 0.01 V into 1 V.First explained in Clap-On Light →
H
- H-bridge
- Four switches around a motor, arranged like an H, that can send current through it either way: forwards or backwards.First explained in Wired RC Car →
- Hertz (Hz)
- Vibrations (or flashes, or ticks) per second. A 440 Hz note wiggles the air 440 times a second.First explained in 555 Tone Keyboard →
- High and low
- High means connected to + (ON, 1). Low means connected to − (OFF, 0). An “active low” pin does its job when it’s low.First explained in Flip-Flop Memory →
I
- Infrared
- Light with a color our eyes can’t see. TV remotes use it.First explained in Light Messenger →
- Inhibit (INH)
- A chip input that, while it’s on, makes the chip ignore its clock: everything freezes.First explained in Reaction Timer Game →
- Input
- Where something goes in. On a chip, a pin the chip listens to.First explained in Traffic Light Picker →
J
- Jumper wire
- A short wire with a stiff tip on each end, made for plugging into breadboards.First explained in Light Up an LED →
L
- Lead
- Said “leed”. A wire that connects something (like a sensor or a part) to your circuit.First explained in Steady-Hand Game →
- LED
- Light-Emitting Diode: a tiny light that only lets current through one way. The long leg goes toward +.First explained in Light Up an LED →
- Light sensor (LDR)
- Light-Dependent Resistor: a resistor whose value drops when light shines on it.First explained in Night Light →
- Logic
- Simple rules that turn yes-or-no inputs into a yes-or-no answer. Computers are built from it.First explained in Secret Code Lock →
- Logic gate
- A tiny circuit inside a chip that follows one logic rule (AND, OR, XOR…).First explained in Logic Gate Puzzles →
M
- Mains electricity
- The electricity from the sockets in your walls. It’s powerful enough to hurt you badly, so never use it for projects.First explained in Light Messenger →
- Microcontroller
- A tiny computer on a single chip, which you program to control a gadget.First explained in Wired RC Car →
- Microfarad (µF)
- The unit for how much charge a capacitor holds (how big the bucket is).First explained in Glow That Fades →
- Microphone
- A part that turns sound into electricity. An electret microphone has a thin sheet inside that wobbles with the sound.First explained in Clap-On Light →
- Morse code
- An old way of sending letters as short and long signals (dots and dashes), each letter its own pattern.First explained in Push-Button Light →
- Motor
- A part that spins when current flows through it, using magnets and coils of wire.First explained in Spinning Fan →
- Multiplier
- The third band on a resistor. It tells you how many zeros to add after the first two digits.First explained in Meet Electricity →
N
- Noise (electrical)
- Tiny random electric wiggles picked up from the air. They can make an unconnected chip input act randomly.First explained in Logic Gate Puzzles →
- Notch
- The little dip (or dot) at one end of a chip. It shows which end is which, so you can find pin 1.First explained in 555 Blinker →
O
- Octave
- The same note, only higher or lower: going up an octave doubles the vibrations per second.First explained in 555 Tone Keyboard →
- Ohm (Ω)
- The unit for measuring resistance. 1 kΩ (kilo-ohm) is 1,000 ohms, and 1 MΩ (mega-ohm) is a million.First explained in Meet Electricity →
- Op-amp
- A general-purpose amplifier chip. A couple of resistors set exactly how much bigger it makes a signal.First explained in Clap-On Light →
- Open circuit
- A circuit with a gap in it somewhere, so no electricity can flow.First explained in Meet Electricity →
- Optocoupler
- A chip with a hidden LED and a light-sensitive transistor inside. It passes a signal between two circuits using only light.First explained in Light Messenger →
- OR
- A logic rule: the answer is yes (1) if any input is yes.First explained in Secret Code Lock →
- Output
- Where a result comes out. On a chip, a pin where it sends out its answer: ON (connected to +) or OFF (connected to −).First explained in 555 Blinker →
P
- Parallel
- Parts connected side by side, so each one has its own path from + to −.First explained in Two LEDs: Series vs. Parallel →
- Passive buzzer
- A buzzer with no circuit inside. It needs electricity switching on and off very fast (from a timer chip) to make a note.First explained in Doorbell Buzzer →
- Pin
- One of a chip’s metal legs. Each pin has a number and a job.First explained in 555 Blinker →
- Pitch
- How high or low a note sounds. More vibrations per second means a higher pitch.First explained in Light Theremin →
- Polarized
- Has a + leg and a − leg, so it must go in the right way round. LEDs and can-shaped capacitors are polarized.First explained in Glow That Fades →
- Potentiometer (pot, knob)
- A resistor with a knob. Turning the knob slides a contact (the wiper) along it, changing the resistance.First explained in Dimmer Knob →
- Power rail
- The long + and − strips along the edges of a breadboard. Plug the battery in here and power is easy to reach from anywhere.First explained in Meet Electricity →
- Power-on reset
- A resistor and capacitor that hold a chip’s reset for a moment when the batteries go in, so it always starts the same way.First explained in Clap-On Light →
- Pull-down resistor
- A resistor that gently connects a chip input to −, so it reads a clear 0 when nothing else is connected.First explained in Logic Gate Puzzles →
- Pull-up resistor
- A resistor that gently connects a point to +, so it stays high unless something stronger pulls it down.First explained in Tripwire Alarm →
- Pulse
- A quick ON, then OFF again.First explained in Flip-Flop Memory →
- Push button
- A switch that’s only closed while you press it. A spring pops it open again when you let go.First explained in Push-Button Light →
R
- Radio waves
- Invisible waves, like light our eyes can’t see, that carry sound and information through the air.First explained in AM Radio →
- RAM
- The memory a computer uses while it’s working. It’s made of billions of tiny memory cells.First explained in Flip-Flop Memory →
- Random
- Impossible to predict, like the roll of a dice.First explained in Electronic Dice →
- Rated (voltage rating)
- The most volts a part can safely take. It’s printed on capacitors.First explained in Glow That Fades →
- Reset
- An input that sets a chip back to the start: a counter goes back to 0.First explained in 555 Blinker →
- Resistance
- How much something slows the flow of electricity down, like a narrow part of a pipe. Measured in ohms (Ω).First explained in Meet Electricity →
- Resistor
- A part that holds current back, like a narrow pipe. It protects delicate parts like LEDs from getting too much current.First explained in Meet Electricity →
- Ribbon cable
- Several thin wires stuck side by side in a flat strip.First explained in Wired RC Car →
S
- Schematic
- A map of a circuit drawn with symbols. It shows what’s connected to what, not where things sit on the board.First explained in Light Up an LED →
- Sensor
- A part that notices something about the world (light, heat, water) and changes its electricity because of it.First explained in Night Light →
- Series
- Parts connected one after another, in a single line, so the same current goes through all of them.First explained in Meet Electricity →
- Short circuit
- When + and − get joined with almost nothing in between. Far too much current flows and things get hot. Always avoid it!First explained in Meet Electricity →
- Signal
- Electricity that changes (on and off, or up and down) to carry a message: a note, a number, or “someone pressed the button”.First explained in Light Theremin →
- Slide switch
- A switch with three legs: sliding it connects the middle leg to one side or the other.First explained in Traffic Light Picker →
- SPDT
- Single Pole, Double Throw: a switch with one input that can connect to either of two outputs.First explained in Traffic Light Picker →
- Switch
- A gate in a circuit’s loop. Open, there’s a gap and nothing flows; closed, the loop is complete.First explained in Push-Button Light →
T
- Tank steering
- Steering by running the left and right wheels at different speeds or directions, like a tank.First explained in Wired RC Car →
- Thermistor
- A resistor whose value changes with temperature. An NTC thermistor’s resistance goes down as it warms.First explained in Fever Alarm →
- Time constant
- Resistance × capacitance: roughly how many seconds a capacitor takes to fill or empty through a resistor.First explained in Glow That Fades →
- Toggle
- To flip to the opposite: on becomes off, off becomes on.First explained in Flip-Flop Memory →
- Tolerance
- How exact a resistor is. A gold band means its real value is within 5% of what the bands say.First explained in Meet Electricity →
- Transistor
- An electronic switch with three legs. A tiny current into the base lets a much bigger current flow from the collector to the emitter.First explained in Transistor Switch →
- Truth table
- A table listing every way the inputs could be set, and the answer for each one.First explained in Secret Code Lock →
V
- Variable resistor
- A resistor whose value you can change, for example a potentiometer with only two legs used.First explained in Dimmer Knob →
- Voltage (volts, V)
- How hard electricity is pushed, like the pressure from a water pump. A battery’s voltage is written on it: an AA battery is 1.5 volts.First explained in Meet Electricity →
- Voltage divider
- Two resistors in a row between + and −. The point between them sits at a voltage in between, decided by which resistor is bigger, like a tug-of-war.First explained in Night Light →
- Volume
- How loud a sound is.First explained in Dimmer Knob →
W
- Wiper
- The middle leg of a potentiometer: a little metal finger that slides along the resistance strip as you turn the knob.First explained in Dimmer Knob →
X
- XOR (exclusive or)
- A logic rule: the answer is yes (1) if exactly one input is yes, but not both.First explained in Logic Gate Puzzles →