Beginner · Project 10
Steady-Hand Game
Bend a wire maze and guide a wire loop along it without touching. If you touch it, the buzzer sounds, the light flashes, and you're caught!
Build this only with an adult present. Before you start, read our safety notice and disclaimer.
🧰 What you need
- 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
- 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
- 3×AA batteryA regular household battery. Each one gives 1.5 volts.
- 1×220 Ω resistor — red, red, brown, goldOur go-to LED resistor. Colors: red, red, brown, gold.
- 1×5 mm LED (any color) — any color worksA tiny light that only lets current flow one way. The long leg is +.
- 1×Active buzzer, 5 V — an active buzzer, like in the Doorbell projectBeeps all by itself when you connect it to a battery. Long leg is +. (A "passive" buzzer only clicks.)
- 1×Stiff bare wire — about 50 cm for the maze, plus 15 cm for the wandUncoated craft wire (or a straightened paper clip) you can bend into shapes.
- 4×Jumper wire — two of them long, or male-to-femaleA short wire with stiff ends that push into the breadboard.
- 1×Modeling clay or play-dough — two lumpsTwo lumps make great stands to hold wire shapes up off the table.
✨ The finished project
🔣 New schematic symbols
This project’s schematic has some symbols you haven’t seen before. Here’s what they mean.
- Touch points
Two open circles are bare metal ends that aren’t joined. The circuit only connects when something bridges them: a finger, a drop of water, or a wire.
You’ve learned that a switch is just two pieces of metal that touch to complete a loop. So anything metal can be a switch, even a wiggly wire! In this game you guide a wire loop (the wand) along a bent wire (the maze) from one end to the other. Touch the maze and the circuit closes: the buzzer sounds, the LED flashes, and you’re caught! 🚨
Make the maze and wand
The maze: bend about 50 cm of stiff bare wire into wiggles, loops and hills. Make the first one easy and the rest trickier! Leave about 3 cm straight at each end.
The stands: push each straight end into a lump of modeling clay so the maze stands up off the table.
The wand: bend a 15 cm piece of wire into a small loop (about the size of a coin) at one end. Thread it onto the maze before you stick in the second end! The rest of the wire is the handle. Wrap tape around the handle so your fingers don’t touch the metal.
Build the circuit
Buzzer: long (+) leg in e7, short leg in e4. It must be an active buzzer (see Doorbell Buzzer).
Black wire for the buzzer: a4 to T-4 (top blue − rail, column 4).
Resistor: b7 (the same column as the buzzer’s + leg) to b11.
LED: long leg in e11, short leg in e12.
Black wire for the LED: a12 to T-13 (top blue − rail, column 13).
Maze lead (a lead, said “leed”, is a wire that connects something to your circuit): push one end of a long jumper wire into a7, the column shared by the buzzer and the resistor. Wrap the other end tightly around one end of the maze, or use an alligator clip (a spring-loaded metal clip with teeth).
Wand lead: push one end of another long jumper into T+15 (top red + rail, column 15). Wrap the other end around the wand’s handle under the tape.
Power: battery red wire into T+1, black into T-2. Touch the wand to the maze to test it: BZZT and a flash! Hold it steady and everything is quiet.
How it works
The wand is connected to the battery’s +. The maze is connected to a column that feeds two paths side by side (in parallel, like project 4):
- Path 1: the buzzer, straight to the − rail. (Active buzzers limit their own current, so they don’t need a resistor.)
- Path 2: the 220 Ω resistor and the LED, to the − rail.
While the wand and maze don’t touch, there’s a gap, so nothing flows and both stay off. The moment metal touches metal, the gap closes and both paths get power at once. You’ve made your own switch, and it’s really sensitive!
Play!
- Start with the wand loop at one end of the maze.
- Move it slowly to the other end without touching.
- Every flash counts as a touch. Fewest touches wins!
- Make it harder: time each other, use your other hand, or bend a new, wigglier maze.
Not working?
- Nothing happens when touching? The wire might have a clear coating on it, so scrape the ends with sandpaper. Also check the leads are wrapped tightly around bare metal.
- LED flashes but no sound, or only a click? Check the buzzer’s long leg is in e7. If it only clicks, it’s a passive buzzer, and you need an active one.
- Buzzing all the time? The wand loop might be resting on the maze, or the two leads might be touching each other.
- Test the board part: touch the two jumper ends together. If it buzzes and lights, the breadboard part is fine.